Aaron BensonREALTOR® · Realty ONE GroupTalk to Aaron

Land

Paradise Valley lot and building rules: R-43, floor area, height and hillside

The short answer

Most of the Town of Paradise Valley is zoned R-43, where the Town’s tables set a minimum lot of 43,560 square feet (one acre), a minimum width of 165 feet, setbacks of 40 feet front and rear and 20 feet side, a 25% floor area ratio, two stories and, on a lot under 3 acres, a height of 24 feet not counting chimneys.

Land counts as hillside if it’s in the Town’s Hillside Development Area or the natural slope under the building pad is 10% or more, and then new work needs the Hillside Building Committee’s approval before the Town issues a permit. A parcel’s zoning and hillside status decide what applies, so check them with the Town before relying on any figure.

The R-43 rules in one table

New building on an R-43 lot outside the hillside area follows this table. The Town’s Resident Guide (revised 2023) says most of the Town is zoned R-43.

The figures in this guide come from the Town’s zoning ordinance, checked on November 2, 2026. Rules change and parcels differ, so confirm any lot with the Town’s Community Development Department at 480-348-3692 before relying on them.

Rule R-43 lot Town source
Minimum lot size 43,560 sq ft Table 1001-A1
Minimum lot width 165 ft Table 1001-A1
Front setback, main house 40 ft Table 1001-A1
Side setback, main house 20 ft Table 1001-A1
Rear setback, main house 40 ft Table 1001-A1
Side or rear setback with frontage 40 ft Table 1001-A1
Maximum floor area ratio 25% Table 1001-A1
Minimum floor area 2,000 sq ft Table 1001-A1
Stories, main house 2 Table 1001-A1
Height, lot under 3 acres 24 ft, not including chimneys Table 1001-A2
Height, lot of 3 to under 4 acres 26 ft, not including chimneys Table 1001-A2
Height, lot of 4 acres or more 30 ft, including chimneys Table 1001-A2
Open space plane Starts 16 ft above the 20-ft setback line, then rises 20% toward the center of the lot Section 1001
Accessory building 1 story, 16 ft high. Setbacks: 60 ft front, 20 ft side, 20 ft rear, 40 ft side or rear with frontage Table 1001B
Accessory ground area No more than half the ground area of the main building Section 1005

In square feet, 3 acres is 130,680 and 4 acres is 174,240, using the 43,560 square feet to the acre in the Town’s hillside article.

How floor area is counted

The 25% limit counts all area under roof, including any second story, so a 43,560-square-foot lot can have at most 10,890 square feet of floor area.

The Town’s certification form says the total also includes:

  • the garage, a guest house, and accessory buildings such as gazebos and ramadas;
  • the solid parts of trellises and open weave roofs;
  • a courtyard, when its walls are over 6 feet tall or the house itself forms it on more than three sides.

Once a plan reaches 22% or more, within 3% of the limit, the Town requires a certification stamped by an Arizona engineer or land surveyor at the roof nail or framing inspection.

How height is measured

The main house has to pass two separate height tests: the maximum height in the table and the open space plane.

  • Maximum height is measured from the lowest natural grade below the structure to its highest point. If the ground was excavated below that and not restored against the walls, it’s measured from the lowest excavated grade next to the walls. The Town takes a wash or similar anomaly out of the calculation.
  • The open space plane applies to R-43 and R-175 lots outside the hillside area. The Town’s handout calls it an “imaginary tent”: 16 feet at the 20-foot setback line, 20 feet at the 40-foot line and 24 feet at the 60-foot line, measured from the natural grade at the 20-foot line.

So a house close to the setback line can’t reach the lot’s maximum height at that point, even on a lot allowed 24 feet or more.

Basements

The floor area of a fully subterranean part of a building doesn’t count toward the floor area ratio, while any part that isn’t fully subterranean does.

The ordinance defines a basement as a story with more than half its height below natural grade. Basement exits count toward floor area and have to meet the setbacks, except standard window wells. The Town’s policy on subterranean patios adds its own setback rules, which depend on how deep the space is and how it’s retained, so ask the Town about any below-grade outdoor space.

Hillside requirements: what counts as hillside and who approves it

Land is hillside if it’s in the Hillside Development Area on the Town’s map, or if the natural terrain under the building pad has a slope of 10% or more, whether or not the map shows it. Outside the mapped area, a 10% slope created by a natural wash on land that wouldn’t otherwise be hillside is exempt.

The Town can’t issue a building permit for new hillside work until the Hillside Building Committee, or its chair where the ordinance allows, has approved it. On hillside land:

Rule Hillside land
Main building height A 24-ft plane parallel to the natural grade, in place of the table above
Accessory height A 16-ft plane parallel to the natural grade
Overall height 40 ft at most, highest point to lowest natural grade, chimneys and accessory buildings included
Setbacks The underlying zoning district’s
Disturbed land A share of the lot set by the building site’s slope: 60% at a 10% slope, 10% at 38% to 40%, 4% at 100%
Mountain ridge lines No development that alters the mapped ridge lines at or above 1,500 ft

Rebuilding or remodeling an older home

A new house has to meet the current tables. A home that was legal when built but no longer meets them is a nonconforming structure, and Article XXIII limits what happens to it:

  • Remodels: work can’t add to an existing encroachment into a setback, or to the height of the nonconforming part.
  • The 50% rule: if structural work under permits issued within 36 months covers more than 50% of the original square footage, the whole structure has to be brought up to the rules for new structures. Painting, flooring, cabinets and appliances don’t count.
  • Additions: any new addition has to meet the current code.
  • Maintenance: normal upkeep and minor repairs are allowed if the cost in any 36 months stays within 30% of the structure’s current full cash value on the County Assessor’s records.
  • Damage from fire, flood, wind or lightning: the structure can be rebuilt with the same setbacks, height, footprint and square footage if permits are secured within 12 months. Any change to the part being rebuilt means that whole part has to meet the current code.

A nonconforming lot is one that met the rules when it was recorded but doesn’t now meet the minimum area, width or access. It can still be used for any principal use the zone allows, and new structures on it have to meet the rest of the code. The Resident Guide says some R-43 lots were already under the minimum when they were annexed.

The other residential districts

The Town’s other residential districts run from 10,000 to 175,000 square feet.

District Lot (sq ft) Width (ft) Front, side, rear (ft)
R-175 a 175,000 165 40, 20, 40
R-175 b 175,000 165 100, 20, 100
R-43 43,560 165 40, 20, 40
R-35 35,000 150 40, 20, 40
R-35A 35,000 150 40, 15, 40
R-18 18,000 120 40, 20, 40
R-18A 18,000 120 35, 10, 35
R-10 10,000 100 20, 7, 25

The lot and width are minimums, and the setbacks are minimums for the main building.

  • R-175 a has a primary building built before June 13, 1991, and R-175 b doesn’t.
  • R-175 side setbacks are 40 feet for a building with two stories or over 24 feet, and 20 feet for one story no taller than 24 feet.
  • R-35 and R-35A side setbacks are 40 feet for a second story, and for any part of a single story higher than 24 feet.
  • Side or rear setback with frontage is the same as the rear setback in the table, except in R-10, where it’s 20 feet.
  • Stories are 2 in R-175, R-43 and R-35, and 1 in R-35A, R-18, R-18A and R-10.
  • R-10 yards can instead follow a previously recorded plat, or what existed when the land was annexed.
  • Maximum floor area ratio is 25% in each district except R-10, which has none.
  • Minimum floor area is 2,000 square feet in R-175 and R-43, 1,800 in R-35 and R-35A, and 1,500 in R-18, R-18A and R-10.

How to check a parcel

Confirm the zoning first, because every number here depends on it.

  1. Look up the parcel with the Maricopa County Assessor.
  2. Ask the Town’s Community Development Department, 480-348-3692, for the zoning district, whether the land is hillside, and whether the lot or the home is nonconforming.
  3. Read the current Town Code. The tables here come from the Town’s PDF of Article X, which was online as of April 2026 but whose link no longer opens. The Town’s floor area form, revised in February 2026, and its height handout give the same 25%, 24-, 26- and 30-foot figures.
  4. Read the title commitment for recorded restrictions and easements, which apply on top of the zoning.

Who serves the lot is a separate check: see water, sewer and septic in Paradise Valley. For how the Town’s rules differ from the City’s next door, see Paradise Valley vs. Scottsdale. For the City of Phoenix’s large-lot districts in Arcadia, such as RE-35, RE-24 and R1-14, see Arcadia’s zoning and lots. The Paradise Valley page describes the lots and homes there. To talk through a specific parcel, book a consultation.

Key takeaways

  • Most of the Town is zoned R-43, with a minimum lot of 43,560 square feet and a minimum width of 165 feet.
  • Floor area is capped at 25% of the lot, and the total includes the garage, a guest house and accessory buildings.
  • The main house has to pass two height tests: the maximum in the table and the open space plane.
  • New hillside work needs the Hillside Building Committee’s approval before the Town issues a permit.
  • Confirm the parcel’s zoning first, because every figure depends on it.

Questions people ask next

What does R-43 zoning mean in Paradise Valley?

It’s the Town’s district with a minimum lot of 43,560 square feet, a minimum width of 165 feet, setbacks of 40 feet front and rear and 20 feet side, and two stories. Most of the Town is zoned R-43.

How large a house can go on a 43,560-square-foot R-43 lot?

The 25% limit counts all area under roof, including any second story, so a 43,560-square-foot lot can have at most 10,890 square feet of floor area.

How tall can a house be?

On an R-43 lot under 3 acres, 24 feet, not including chimneys. It’s 26 feet on 3 to under 4 acres, and 30 feet, chimneys included, on 4 acres or more.

What are the hillside requirements?

On hillside land the main building’s height is a 24-foot plane parallel to the natural grade, nothing may be taller than 40 feet overall, and the share of the lot that can be disturbed depends on the building site’s slope.

Who confirms a parcel’s zoning?

The Town’s Community Development Department, 480-348-3692. Ask it for the zoning district, whether the land is hillside, and whether the lot or the home is nonconforming.

About this guide

General information, not legal, tax or financial advice. Your own contract controls, and your attorney, tax professional or other advisers can confirm what applies to you.

Sources checked November 2, 2026. Rules and figures can change.

Sources

  1. Town of Paradise Valley Zoning Ordinance, Article X, Height and Area Regulations: Tables 1001-A1, 1001-A2 and 1001B (effective February 26, 2021, Ordinance 2021-01). The Town's PDF as archived April 14, 2026, accessed November 2, 2026web.archive.org
  2. Town of Paradise Valley Zoning Ordinance, Article XXII, Hillside Development Regulations (effective November 24, 2018, Ordinance 2018-15), accessed November 2, 2026paradisevalleyaz.gov
  3. Town of Paradise Valley Zoning Ordinance, Article XXIII, Nonconformance. The Town's PDF as archived April 14, 2026, accessed November 2, 2026web.archive.org
  4. Town of Paradise Valley, Floor Area Ratio (FAR) Certification (revised February 17, 2026), accessed November 2, 2026paradisevalleyaz.gov
  5. Town of Paradise Valley, Open Space Criteria and Building Heights, accessed November 2, 2026paradisevalleyaz.gov
  6. Town of Paradise Valley, Basements and subterranean outdoor space in F.A.R. calculations and setbacks, accessed November 2, 2026paradisevalleyaz.gov
  7. Town of Paradise Valley, Resident Guide (revised 2023): zoning, accessed November 2, 2026paradisevalleyaz.gov
  8. Maricopa County Assessor, parcel search, accessed November 2, 2026mcassessor.maricopa.gov

Next steps

Almost done: check your email

We sent a link to

Wrong address?

  1. Open the email fromAaron Benson, Realty ONE Grouphomes@updates.aaronbenson.com
  2. Tap “Confirm my alerts”

The link works for 7 days. It usually arrives within a few minutes, and on a very busy day by the next morning. If you can't find it, check your spam or promotions folder.

Only want certain streets in Paradise Valley?Watch a street, or draw your own area

Or ask Aaron directly.Ask about a home I’m considering

Questions about your own move?

Aaron answers them personally, in person, by phone or on video.

Ask Aaron about a property

Still deciding whether to move? That’s a good time to talk.

Call 602-785-5095Text 602-785-5095